Do It Yourself Bath Setup.
Do It Yourself Bath Setup.
Blog Article
Everybody may have their own individual way of thinking on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old tub is easily accessible, the job can relocate rapidly; if you need to open a wall surface to remove the old tub and also position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. Make certain you have qualified yourself for the task and also are comfortable trying it. Rather than employing a specialist to take control of a halfway-completed job, it is far better to take into consideration employing one prior to you start. Chances are you might require a professional plumber to make tube links.
This write-up will certainly help you install a new tub in your washroom if you have actually currently bought a brand-new tub and don't require to alter the plan of your previous water system pipelines.
Your tools and also product checklist should comprise the following:
Planning for the Installation
Firstly, the supporting framework provided with the bath must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now prepare to be suited its last position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from turning throughout this process. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Tub
Making use of both wooden boards under its feet, position the bathtub in the called for setting. The wood boards are practical in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bathtub up until the level checks out degree.
To install taps, fit all-time low of the furthest versatile tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the water system and inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Fill up the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the producer's user's manual. Tiling and securing around the bath tub should wait until the tub has actually been utilized at the very least once as this will resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in place with the supplier provided backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The previous type should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and installations. They are sold in tubes and also cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can fracture relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the market. It is advisable to fit the floor tiles utilizing waterproof or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while exploring the internet. You should take the opportunity to share this blog post if you liked it. Thanks for going through it.
Book Service Report this page